Nec Versa Lxi Driver For Mac
Model: Nec Versa E680 Type: Notebook Series: Nec Versa Notebook E Series Compatibility: Windows XP, Windows XP 32-bit, Windows XP 64-bit It is recommended to install all the drivers listed below. Utilities and patch are optional, install it only if you need it. If you have question or feedback you can leave your comments below or if you need driver for different model you Download and double click to install the driver.
Nec Versa E680 Card Reader Driver ENE CB710 Multicard Driver 1.12.02 Nec Versa E680 Chipset Win Driver Intel Chipset Driver 4.30.1006 Nec Versa E680 Modem Driver Smart Link MDC56S-I MDC Modem 3.20.3.597 Nec Versa E680 Network-LAN/Ethernet Driver Via VT6103/5 Rhine II/III drivers Nec Versa E680 Audio Driver Realtek ALC202 audio driver 5.10.0.5170 Nec Versa E680 Touchpad Driver Synaptics Touch Pad Driver 7.10.10 Nec Versa E680 Graphic Driver Intel Extreme Graphics 6. Nec Versa E680 Wireless Driver.Select one, install only one base on your specification 1- Intel Wireless Pro 2100 B Driver 1.2.4.35 2-Intel PRO/Wireless 2100 LAN Adapter Nec Versa E680 Patch: Microsoft Quickfix KB828012 - NAV/NIS 2004 installation Word 2002 Service Pack Installation Patch PX Engine Update Nec Versa E680 Utilities: Download Full.zip Download Full.rar Download Full.iso.
. NEC Versa Notebook Computer N E C V ® E R S A S E R V I C E A N D R E F E R E N C E M A N U A L. Reproduction of this document or portions thereof without prior written approval of NECC is prohibited. NEC and Versa are registered trademarks of NEC Corporation and/or one or more of its subsidiaries. All are used under license. Contents Preface.vii Abbreviations.ix 1 System Overview Getting to Know the NEC Versa.1-2 The Front of the System.1-3 LCD Panel.
1-3 Base Unit.1-3 Operating Status LEDs.1-4 Power Button.1-4 Keyboard.1-5 Front Features.1-7 The Back of the System. NEC Utilities. 2-26 NEC Customize Utility.
2-26 NEC Customize Utility Screen.2-26 Using the NEC Customize Utility.2-27 HDPREPEZ Utility.2-27 Using HDPREPEZ in Windows 98 or 95. 2-27 Using HDPREPEZ with Windows NT.2-27 Application and Driver CD. Connector Board. 3-28 Reassembly.3-29 4 System Board Layout LED Status Board.4-2 Audio Board.4-2 Connector Board.4-2 Main Board.4-3 5 Illustrated Parts Breakdown Illustrated Parts Breakdown. 5-2 Parts List. 5-3 6 Preventive Maintenance Cleaning the Notebook Exterior. LXi notebook computer.
The manual also provides hardware and interface information for users who need an overview of the system design. The manual is written for NEC-trained customer engineers, system analysts, service center personnel, and dealers. The manual is organized as follows: Chapter 1, “System Overview,”.
Abbreviations ampere error checking and correction alternating current enhanced capabilities port Advanced Graphics Port extended data output advanced technology Enhanced Graphics Adapter (IBM PC) enhanced parallel port Bulletin Board Service EPROM erasable and programmable binary-coded decimal BIOS Customized Utility EVGA Enhanced Video Graphics Array BIOS. pound slave light-emitting diode SCSI Small Computer System Interface liquid crystal display SDRAM synchronous dynamic least-significant bit random-access memory large-scale integration signal ground mega SIMM single inline memory module milliamps standard page mode maximum Sound Retrieval System megabyte SVGA Super Video Graphics Array Monochrome Display Adapter switch modified frequency modulation. System Overview Getting to Know the NEC Versa The Front of the System The Back of the System The Left Side of the System The Right Side of the System The Bottom of the System Internal Components Chipset. Getting to Know the NEC Versa The NEC Versa LXi notebook computer offers you a portable system filled with exciting ® resources for home, business or travel.
Standard features include a powerful Intel Pentium III 450-MHz, 500-MHz, 600-MHz with SpeedStep™, or 650-MHz with SpeedStep microprocessor, all with AGP (advanced graphics port). (LCD) panel. LCD Panel Your NEC Versa LXi comes with a 1024x768, 64K color LCD panel that you can adjust for a comfortable viewing position. To adjust the viewing angle, gently tilt the LCD panel into position. Depending on the model, your system is equipped with a: 14.1-inch color Thin Film Transistor (TFT) Extended Graphics Array (XGA) panel, or a. G – Power Button D – Scroll Lock IDE/VBIII devices — lights when the NEC Versa writes data to or retrieves data from the internal hard disk drive, a SuperDisk drive in the file bay, or a device in the VersaBay III.
Hibernate – Press the Power button to put the system into Hibernate mode. Shutdown – Press the Power button to shutdown (power off) the system. Keyboard The NEC Versa keyboard offers the following features, which are described after the figure. Keyboard A – Function Keys D –. No function when Windows 98 configured for Advanced Configuration and Power Interface (ACPI). — Sets the beeper volume to low, medium, high, or mute. Fn-F6 — Toggles between various power management levels in Windows 95.
Beeps Fn-F7 indicate the level chosen as follows: 1 beep 2 beeps Custom. D – LCD Lid Latch NEC VersaBay III™ — A 24X CD-ROM drive, a SuperDisk drive, a 6X DVD-ROM drive, or a CD read/write drive comes installed in the NEC VersaBay III on the front of your system. The VersaBay III lets you add options, including an optional second Li-Ion battery, or an additional hard disk drive.
NEC Versa Dock is specially designed to allow for proper system cooling. AC Power Port — Use the power jack to attach the NEC Versa to a DC power source, such as the AC adapter or the optional DC auto adapter. The Left Side of the System The left side of your NEC Versa offers the following features, which are described after the figure. Left side features A – TV Out (S-video) E – LAN Port (optional) B – TV Out (RCA) F –. Plugging in an external microphone disables the built-in microphone. IR Port — Use this infrared (IR) port to transfer files between your NEC Versa and an IR-equipped desktop or notebook computer or to print to an IR-capable printer.
NEC VersaBay III™ Release Lock — Unlocks the VersaBay III for device removal. NEC VersaBay III — A 24X CD-ROM drive, a SuperDisk drive, or a 6X DVD-ROM drive, or a CD read/write drive comes installed in the NEC VersaBay III on the front of your system. The twelve-cell Lithium-Ion (Li-Ion) battery provides the main power source in your NEC Versa LXi computer. See Chapter 9 for a list of battery specifications. In addition to this battery, the CMOS battery and bridge battery also provide system power.
ChipSet The following table provides information on the system chipset. System Chipset Chip Manufacturer Description Pentium III Intel 450-MHz with AGP 450 MHz CPU 500-MHz with AGP 500 MHz CPU 600-MHz with AGP and SpeedStep 600 MHz CPU 650-MHz with AGP and SpeedStep 650 MHz CPU Mobil Triton II and 82371MB PIIX4M Intel. System Configuration and Setup Power Sources for Your NEC Versa BIOS Setup Updating the BIOS NEC Utilities Application and Driver CD.
Read the following sections for specific information about using the NEC power sources. Using the AC Adapter Use the AC adapter and power cable that came with your NEC Versa to run your computer on alternating current (AC) power, or to recharge the battery pack. Use the AC adapter whenever a wall outlet is nearby. Do not cover or place objects on the AC adapter. Keeping the adapter clear of objects lets the adapter cool properly during use.
Only use the AC adapter that comes with your Versa LXi. Although other adapters look similar, using them can damage your system. In addition to the system’s power meter, you can determine battery status via the battery gauge LEDs on the front of the Lithium-Ion battery that ships with your NEC Versa LXi computer. For details about the battery gauge LEDs, refer to the next section, “Battery Gauge LEDs.”. Power off the system, remove the battery pack and replace it with a fully charged battery. Leave the battery pack in the system and connect your NEC Versa to the AC adapter and a wall outlet. If you connect the system to AC power and keep the system within standard operating temperatures, the battery recharges in approximately 2–3 hours.
Battery Handling Keep the following in mind when removing or replacing a battery. Use only the battery designed for your system in the NEC Versa. Mixing other manufacturers’ batteries, or using a combination of very old and new batteries can deteriorate battery and equipment performance. Slide the battery release latch toward the back of the system and hold firmly. Locating the battery bay release latch A – Battery Release Latch Continue to hold the battery release latch as you slide the battery out of the system. Removing the battery System Configuration and Setup 2-7. Insert the new battery as follows: Locate the alignment groove on the edge of the battery.
Locate the alignment groove inside the battery bay. Align the grooves on the battery with the grooves in the bay. Slide the battery into the bay until securely locked into place. Inserting the battery Turn over the system.
Read the instructions that came with the battery charger before charging the battery. System Batteries Your NEC Versa is equipped with a main, Lithium-Ion battery and two backup batteries that help to prevent data loss. In addition, your system provides the option to install a second Lithium-Ion battery in the VersaBay III, extending battery life when away from an AC power source.
The twelve-cell Lithium-Ion (Li-Ion) battery provides the main power source in your NEC Versa LXi computer. See Chapter 9 for a list of battery specifications. In addition to this battery, the CMOS battery and bridge battery also provide system power. If the system detects an error during POST, it prompts you with a double beep and a message: “Press to resume.” If you press, the system enters BIOS Setup automatically. If you want to fix the error, carefully read the error message that appears above the prompt (taking notes if you want), and press.
Looking at Screens BIOS setup screens have three areas as shown next. Advanced CMOS Setup Parameters — The left side of the screen. This area lists parameters and their current settings. Available Options and Help — The right side of the screen.
This area lists alternate settings and Help text for each parameter. Checking/Setting System Parameters The BIOS Setup utility consists of a number of screens, each representing a specific area of the BIOS. The following tables list the BIOS parameters, their factory default settings, alternate settings, and a description of each setting. See the item-specific help that appears on each Setup screen for more details.
SuperDsk, Not installed These setup items are only visible when the system is docked Date — Sets your NEC Versa’s calendar month, day and year. The calendar clock is year 2000-compliant. These settings remain in memory even after you turn off system power. LCD Panel View Expansion — Specifies whether the panel view is reduced/off or expanded/on. PS/2 Port Warm Swap — Specifies whether or not you can swap a PS/2 device during system suspension. Internal Mouse — Specifies whether or not you can use both the internal and the external mouse. Control Panel, Power Management Properties, Advanced.
Hard Disk Drive Passwords Your NEC Versa allows you to establish password protection for the internal hard disk drive and for an optional hard disk drive installed in the NEC VersaBay III. Hard disk drive (HDD) password protection restricts access to the drive, if the drive is removed from your NEC Versa and installed in another system. If the hard drive is installed in another NEC Versa system with hard disk drive security enabled, the password must be entered to allow access to the hard drive.
If this NEC Versa system does not support hard disk drive security, you cannot access the data on the hard drive. Power Management Setup If your Versa LXi system ships with the Windows 98 operating system, the Advanced Configuration and Power Interface (ACPI) controls most power management functions through the Power Management Properties screen in Windows. For details about ACPI power management, see the section, “Managing System Power,”. Power Management Under AC — Specifies whether to enable power management features when AC power is in use. When AC power is connected to your NEC Versa system, power management is usually disabled. If you enable this parameter, the system automatically activates the power management profile you set, even when AC power is used. Quick Boot — Specifies whether or not the system performs all tests during system boot.
Silent Boot — Specifies whether or not to display the NEC logo during the system boot. Boot Display Device — Specifies the default display device(s) for the system. Other Boot Devices — If yes, BIOS tries to boot from other boot devices if all selected boot devices fail to boot. IDE Hard Drive — Selects priority of IDE hard drives for boot devices. Peripheral Setup The Peripheral Setup menu displays the connection locations between the system and the Input/Output (I/O) ports and lets you specify different port assignments as needed.
Once refreshed, your battery is conditioned to recharge to its full capacity. To recharge the battery, connect your NEC Versa to AC power. This process may take up to four hours to complete.
Auto Configuration with Defaults — Loads default settings. Preparing the BIOS Update Diskette Before using the BIOS update diskette you must make the diskette BIOS flash ready. Refer to the readme.txt file on the diskette before using the diskette. Follow these instructions to prepare the BIOS Update Diskette. Scan your hard drive for any computer viruses. Gently lift up the edge of the keyboard nearest the LCD and slide the keyboard toward the LCD screen to release the tabs that secure it.
Lifting the keyboard Be careful not to disconnect the keyboard or keyboard cable entirely from the system. A message similar to the following appears: The NEC BIOS Update Utility should not be used to modify the BIOS in a Versa system which is docked. If your Versa is docked, please exit the BIOS Update Utility, power down, and undock your Versa before running the utility. For details about enabling and disabling the BIOS flash switch, see the section earlier in this chapter, “Enabling the BIOS Flash Switch.” NEC Utilities NECC provides several programs and routines designed to make your NEC Versa run more efficiently. The NEC utilities include. Using HDPREPEZ in Windows 98 or 95 In Windows 98 or 95, run the HDPREPEZ Utility if you increase the memory capacity in your NEC Versa beyond the factory installed base memory or if you install a generic Windows 98 or 95 operating system. NEC Info Center are provided on the Application and Driver (A&D) CD that ships with your NEC Versa LXi system.
Some of the drivers are already installed as part of your operating system environment. The additional software on the Application and Driver CD lets you take full advantage of your system resources. Installing the A&D Software Once the Application and Driver CD dialog box appears, follow these steps to install the desired software.
Click the selection tab of your choice. Click the desired application, driver, or utility. Click the Install button to install your selection.
Follow the on-screen instructions to install your selection. Disassembly and Reassembly Required Tools and Equipment Upgrade Information Disassembly Reassembly. Hard Disk Drive The hard disk drive is located under the battery bay in your NEC Versa notebook computer. You must remove the system’s main battery before replacing the hard disk drive.
Replace the hard disk drive as follows. Slide the battery release latch toward the back of the system and hold firmly.
Locating the battery release latch A – Battery Release Latch Continue to hold the battery release latch as you slide the battery out of the system. Removing the battery Disassembly and Reassembly 3-3. Remove the disk drive as follows: Remove the screw that secures the hard disk drive.
Place your finger in the center notch of the hard drive lever and pull up the lever. Be sure that both sides of the lever are raised.
If you encounter any resistance when lifting the lever, carefully loosen both sides of the lever before lifting. Once the drive is disconnected, use the lever to lift the drive out of the system. Once removed, only handle the drive by its sides. Lifting the drive out of the bay Replace the new drive as follows: Holding the drive by its sides, pull up the hard drive lever. To avoid damaging the drive, do not hold the drive by the top and bottom. Align the drive connector with the connector in the drive bay.
Pressing against the outer edge of the lever, slide the drive toward the connectors and push firmly to secure the connection. Do not apply pressure to the drive surface as you push. Follow these steps to install and, if necessary, remove a memory module. Only install NEC-supplied/approved memory module options to ensure proper functionality of your NEC Versa notebook computer.
Contact your NECC dealer for information about available NEC-supplied/approved memory modules. Before handling any internal components, discharge static electricity from yourself and your clothing by touching a nearby metal surface. Turn over the system and locate the memory module bay.
Locating the memory module bay A – Screw B – Memory Module Bay Cover Remove the screw and bay cover. Locate the SO-DIMM expansion port and proceed as follows: Hold the SO-DIMM at a 45 degree angle and align the SO-DIMM contacts with the socket in the system. Label all removed connectors. Note where the connector goes and in what position it was installed. Before handling any internal components, discharge static electricity from yourself and your clothing by touching a nearby metal surface.
Battery Remove the battery pack installed in the NEC Versa LXi system as follows. Disassembly and Reassembly 3-9.
Note Use the batteries in the NEC Versa computer for which they are designed. Also, installing another manufacturer’s battery, or using a combination of very old and new batteries can deteriorate battery and equipment performance.
Power off the system. Close the LCD and turn the system over. Use the following steps to remove a device from the NEC VersaBay III. Close the LCD panel and turn the system over. Locate the NEC VersaBay III release lock and release latch on the bottom of the unit. NEC VersaBay III release lock and latch A –.
Nec Versa Drivers
Pull the device out of the system. Note If you release the latch before completely removing the device, the device casing catches on the inside of the latch. Releasing the device 3-12 Disassembly and Reassembly. Memory Modules Use the following steps to remove a memory module from the system. Before handling any internal components, discharge static electricity from yourself and your clothing by touching a nearby metal surface. Close the LCD panel and turn over the system. Locate the memory module bay.
Locating the memory module bay A –. Hard Disk Drive Use the following procedure to remove the hard disk drive. This procedure assumes the battery has been removed from the system. Close the LCD and turn over the system. Remove the disk drive as follows: Remove the screw that secures the hard disk drive.
Place your finger in the center notch of the hard drive lever and pull up the lever. Once the drive is disconnected, use the lever to lift the drive out of the system. Once removed, only handle the drive by its sides. To avoid damaging the drive, do not hold the drive by the top and bottom.
Lifting the drive out of the bay File Bay Device Follow these steps to remove a device from the file bay. Keyboard and Switch Settings Follow these steps to remove the keyboard and access the switch settings. Before handling any internal components, discharge static electricity from yourself and your clothing by touching a nearby metal surface. Turn the system over and open the LCD panel.
(such as, refreshing a screen, applying gaussian blur, etc.) - If you get the forced termination frequently, disabling OpenMP may help to solve a problem. Bambusa 1.1 free download for mac. • It is available to disable OpenMP. (from the environment setting) - Disabling OpenMP makes processing speed slower. [1.0.24] • Printing functions have been added.
Locate the two keyboard retainers, press and slide each one towards the outside edge of the system. Switch 1, Password Override Switch — The default setting is “OFF.” If you forget your password and cannot access the data on your NEC Versa, change the setting to “ON” and your current password is erased. Locate and remove the six bottom screws securing the front cover. Removing the bottom screws A – Screw Turn the system over and open the LCD panel. Carefully separate and partially lift the front cover from the bottom assembly. Disconnect the VersaGlide cable from connector P8 of the main board. Disconnect the speaker assembly cable from connector P5 from the main board.
Speaker Assembly Use the following steps to remove the speaker assembly from the system. Remove the keyboard and front cover from the system. Locate and remove the six screws securing the speaker assembly. Removing the speaker screws A – Screw Remove the speaker assembly. LED Status Board Use the following steps to remove the LED status board from the system. Remove the keyboard and front cover from the system.
Locate the LED status board and the securing tabs. Locating the board and tabs A – LED Status Board B –. Mini-PCI Option Use the following steps to remove the Mini-PCI option from the system. Remove the keyboard and front cover from the system. Remove the screw from the securing bracket.
Lift the securing bracket and remove from the slit in the main board. Partially lift the Mini-PCI option up and away from the main board and disconnect it from connector P9. The battery is secured with two-sided tape. Carefully pry the CMOS battery up and remove it from the system.
Removing the CMOS battery A – CMOS Battery Buzzer Use the following steps to remove the system buzzer from the system. Remove the keyboard, front cover, PC card assembly, and Mini-PCI option (if present) from the system. Top Cover and LCD Panel Follow this procedure to remove the top cover and LCD panel from the system. Remove the keyboard and front cover from the system. Close the LCD panel and turn the system over. Locate and remove the screw from the file bay. Remove the device from the file bay.
Locate and remove the three screws securing the top cover to the system. Locate and remove the three screws securing the top cover to the system. Locate and remove the screws securing the LCD panel hinges.
Remove the hinge covers. For the 15-inch LCD panel, remove the four screws securing the top cover to the system. Removing the top cover screws A –. Locate and remove the two screws securing the audio board to the system. Removing the audio board screws A – Screw B – Audio Board Lift the audio board up and away from the main board to disconnect it from connector P54.
Remove the audio board. Disconnect the diskette drive cable from connector P4 on the main board. Disconnect the bridge battery cable from connector P1 on the main board. Remove the main board from the system. Bridge Battery Use the following steps to remove the bridge battery from the system. Remove the keyboard, front cover, top cover, and LCD panel from the system.
Locate and remove the two screws securing the fan assembly to the main board. Removing the fan assembly screws A – Screw B – Fan Assembly Disconnect the fan cable from connector P12 on the main board. Remove the fan assembly from the main board. CPU Board Assembly Use the following steps to remove the CPU board assembly.
Nec Versa Lx Driver For Mac
Turn the main board over. Lift the CPU assembly up and away from the main sub-board to disconnect it from connector P8. Remove the CPU board assembly. Connector Board Use the following procedure to remove the connector board from the system. Remove the keyboard, front cover, top cover, LCD panel, Mini-PCI LAN/modem (if present), audio board, and main board from the system. Disconnect the cable from connector P4 on the connector board.
Nec Versa Laptop
Remove the connector board from the system. Reassembly Reassembly is the reverse of the disassembly process.
Use care to insure that all cables and screws are returned to their proper positions. Before handling any internal components, discharge static electricity from yourself and your clothing by touching a nearby metal surface. System Board Layout LED Status Board Audio Board Connector Board Main Board. This following figures show the system boards and connector locations.
LED Status Board A – Connector LP1 Audio Board A – Connector P1 B – Connector P2 Connector Board A – Connector BP3 C – Connector BP4 B – Connector BP1 D –. Main Board A – Connector P4 I – Connector P8 B – Connector P2 J – Connector P9 C – Connector P52 K – Connector P6 D – Connector P1 L – Connector P14 E – Connector P54 M – Connector P12 F –. Illustrated Parts Breakdown Illustrated Parts Breakdown Parts List. Illustrated Parts Breakdown 5-2 Illustrated Parts Breakdown. Parts List The following table contains a listing of the field-replaceable parts and corresponding part numbers.